First login?
Lost password?
 
 
sctp-discussion AT lists.franken.de 
SCTP Discussions

Text archives Help


Aw: Re: [SCTP-Discussion] How to use STT?


Chronological Thread 
  • From: norbert.demeter AT arcor.de
  • To: michael.tuexen AT micmac.franken.de, norbert.demeter AT arcor.de
  • Cc: sctp-discussion AT sctp.de
  • Subject: Aw: Re: [SCTP-Discussion] How to use STT?
  • Date: Tue, 2 Dec 2008 09:04:03 +0100 (CET)
  • List-archive: <http://lists.franken.de/pipermail/sctp-discussion>
  • List-id: SCTP Discussions <sctp-discussion.sctp.de>
Hi Michael,

I am still getting problems like this:

guile> (sctp-as-v-1-1-2 (make-ipv4-address "10.2.111.58") 5000 5000)
<unnamed port>: In expression (associate-from-port peer-addr local-port ...):
<unnamed port>: Unbound variable: associate-from-port
ABORT: (unbound-variable)
guile>

Can you please help?
In the meantime I will try to give the input parameters directly in the .scm
like you proposed.


Thanks a lot,
/Norbert

----- Original Nachricht ----
Von: Michael Tuexen
<Michael.Tuexen AT micmac.franken.de>
An:
norbert.demeter AT arcor.de
Datum: 01.12.2008 19:31
Betreff: Re: [SCTP-Discussion] How to use STT?

> Hi Norbert,
>
> see comments in-line.
>
> Best regards
> Michael
>
> On Dec 1, 2008, at 3:14 PM,
> norbert.demeter AT arcor.de
> wrote:
>
> > Hi,
> >
> > To be honest I do not have much experience with guile and Scheme so
> > some initial help would be very welcome.
> >
> > I would like to get help to run the SCTP testcases included in sctp-
> > test-1.3. What I have done so far was the installing of STT, and
> > replacing the default .scm with one found in the test suite. Problem
> > is that I do not know how to give the input parameters like peer/
> > local addresses, ports, etc. I am getting errors where guile is
> > complaining about certain syntactical errors:
> >
> >
> > guile> (sctp-as-v-1-1-2 ("10.2.111.58" 5000 5000))
> > standard input:1:1: In expression (sctp-as-v-1-1-2 ("10.2.111.58"
> > 5000 5000)):
> > standard input:1:1: Wrong number of arguments to #<procedure sctp-as-
> > v-1-1-2 (peer-addr local-port peer-port)>
> > ABORT: (wrong-number-of-args)
> >
> > Could someone show me examples of running these testcases?
> (sctp-as-v-1-1-2 (make-ipv4-address "10.2.111.58") 5000 5000)
> should work...
>
> You might want to have a look at sctp-param-testtool.scm.
> If you change it to
> (define sut-address (make-ipv4-address "10.2.111.58"))
> (define sut-port 5000)
> (define tester-port 5000)
> and load it then you can use
> (sctp-as-v-1-1-2 sut-addr tester-port sut-port)
> This is exactly the command show in the comment after
> the definition of sctp-as-v-1-1-2.
>
> I hope that helps...
> >
> >
> > Thanks a lot in advance,
> > /Norbert
> > _______________________________________________
> > sctp-discussion mailing list
> > sctp-discussion AT sctp.de
> > http://www.sctp.de/mailman/listinfo/sctp-discussion
> >
>
>
>
> --------------------------------
>
> _______________________________________________
> sctp-discussion mailing list
> sctp-discussion AT sctp.de
> http://www.sctp.de/mailman/listinfo/sctp-discussion
>


Archive powered by MHonArc 2.6.19+.

Top of page