First login?
Lost password?
 
 
sctp-discussion AT lists.franken.de 
SCTP Discussions

Text archives Help


Re: Aw: Re: [SCTP-Discussion] How to use STT?


Chronological Thread 
  • From: Michael Tuexen <michael.tuexen AT micmac.franken.de>
  • To: norbert.demeter AT arcor.de
  • Cc: sctp-discussion AT sctp.de
  • Subject: Re: Aw: Re: [SCTP-Discussion] How to use STT?
  • Date: Tue, 2 Dec 2008 09:12:16 +0100
  • List-archive: <http://lists.franken.de/pipermail/sctp-discussion>
  • List-id: SCTP Discussions <sctp-discussion.sctp.de>
Hi Norbert,

did you also load
sctp.scm
associate-from-port is defined there...

Best regards
Michael

On Dec 2, 2008, at 9:04 AM,
norbert.demeter AT arcor.de
wrote:

Hi Michael,

I am still getting problems like this:

guile> (sctp-as-v-1-1-2 (make-ipv4-address "10.2.111.58") 5000 5000)
<unnamed port>: In expression (associate-from-port peer-addr local- port ...):
<unnamed port>: Unbound variable: associate-from-port
ABORT: (unbound-variable)
guile>

Can you please help?
In the meantime I will try to give the input parameters directly in the .scm like you proposed.


Thanks a lot,
/Norbert

----- Original Nachricht ----
Von: Michael Tuexen
<Michael.Tuexen AT micmac.franken.de>
An:
norbert.demeter AT arcor.de
Datum: 01.12.2008 19:31
Betreff: Re: [SCTP-Discussion] How to use STT?

Hi Norbert,

see comments in-line.

Best regards
Michael

On Dec 1, 2008, at 3:14 PM,
norbert.demeter AT arcor.de
wrote:

Hi,

To be honest I do not have much experience with guile and Scheme so
some initial help would be very welcome.

I would like to get help to run the SCTP testcases included in sctp-
test-1.3. What I have done so far was the installing of STT, and
replacing the default .scm with one found in the test suite. Problem
is that I do not know how to give the input parameters like peer/
local addresses, ports, etc. I am getting errors where guile is
complaining about certain syntactical errors:


guile> (sctp-as-v-1-1-2 ("10.2.111.58" 5000 5000))
standard input:1:1: In expression (sctp-as-v-1-1-2 ("10.2.111.58"
5000 5000)):
standard input:1:1: Wrong number of arguments to #<procedure sctp- as-
v-1-1-2 (peer-addr local-port peer-port)>
ABORT: (wrong-number-of-args)

Could someone show me examples of running these testcases?
(sctp-as-v-1-1-2 (make-ipv4-address "10.2.111.58") 5000 5000)
should work...

You might want to have a look at sctp-param-testtool.scm.
If you change it to
(define sut-address (make-ipv4-address "10.2.111.58"))
(define sut-port 5000)
(define tester-port 5000)
and load it then you can use
(sctp-as-v-1-1-2 sut-addr tester-port sut-port)
This is exactly the command show in the comment after
the definition of sctp-as-v-1-1-2.

I hope that helps...


Thanks a lot in advance,
/Norbert
_______________________________________________
sctp-discussion mailing list
sctp-discussion AT sctp.de
http://www.sctp.de/mailman/listinfo/sctp-discussion




--------------------------------

_______________________________________________
sctp-discussion mailing list
sctp-discussion AT sctp.de
http://www.sctp.de/mailman/listinfo/sctp-discussion





Archive powered by MHonArc 2.6.19+.

Top of page