Chronological Thread 

< Chronological >      < Thread >

---

Hi Michael,

Is there a specific guile command to load .scm files or shall I copy
everything into one .scm before starting STT?

Thanks,
/Norbert


----- Original Nachricht ----
Von: Michael Tuexen
<michael.tuexen AT micmac.franken.de>
An:
norbert.demeter AT arcor.de
Datum: 02.12.2008 09:12
Betreff: Re: Aw: Re: [SCTP-Discussion] How to use STT?

> Hi Norbert,
>
> did you also load
> sctp.scm
> associate-from-port is defined there...
>
> Best regards
> Michael
>
> On Dec 2, 2008, at 9:04 AM,
> norbert.demeter AT arcor.de
> wrote:
>
> > Hi Michael,
> >
> > I am still getting problems like this:
> >
> > guile> (sctp-as-v-1-1-2 (make-ipv4-address "10.2.111.58") 5000 5000)
> > <unnamed port>: In expression (associate-from-port peer-addr local-
> > port ...):
> > <unnamed port>: Unbound variable: associate-from-port
> > ABORT: (unbound-variable)
> > guile>
> >
> > Can you please help?
> > In the meantime I will try to give the input parameters directly in
> > the .scm like you proposed.
> >
> >
> > Thanks a lot,
> > /Norbert
> >
> > ----- Original Nachricht ----
> > Von: Michael Tuexen
> > <Michael.Tuexen AT micmac.franken.de>
> > An:
> > norbert.demeter AT arcor.de
> > Datum: 01.12.2008 19:31
> > Betreff: Re: [SCTP-Discussion] How to use STT?
> >
> >> Hi Norbert,
> >>
> >> see comments in-line.
> >>
> >> Best regards
> >> Michael
> >>
> >> On Dec 1, 2008, at 3:14 PM,
> >> norbert.demeter AT arcor.de
> >> wrote:
> >>
> >>> Hi,
> >>>
> >>> To be honest I do not have much experience with guile and Scheme so
> >>> some initial help would be very welcome.
> >>>
> >>> I would like to get help to run the SCTP testcases included in sctp-
> >>> test-1.3. What I have done so far was the installing of STT, and
> >>> replacing the default .scm with one found in the test suite. Problem
> >>> is that I do not know how to give the input parameters like peer/
> >>> local addresses, ports, etc. I am getting errors where guile is
> >>> complaining about certain syntactical errors:
> >>>
> >>>
> >>> guile> (sctp-as-v-1-1-2 ("10.2.111.58" 5000 5000))
> >>> standard input:1:1: In expression (sctp-as-v-1-1-2 ("10.2.111.58"
> >>> 5000 5000)):
> >>> standard input:1:1: Wrong number of arguments to #<procedure sctp-
> >>> as-
> >>> v-1-1-2 (peer-addr local-port peer-port)>
> >>> ABORT: (wrong-number-of-args)
> >>>
> >>> Could someone show me examples of running these testcases?
> >> (sctp-as-v-1-1-2 (make-ipv4-address "10.2.111.58") 5000 5000)
> >> should work...
> >>
> >> You might want to have a look at sctp-param-testtool.scm.
> >> If you change it to
> >> (define sut-address (make-ipv4-address "10.2.111.58"))
> >> (define sut-port 5000)
> >> (define tester-port 5000)
> >> and load it then you can use
> >> (sctp-as-v-1-1-2 sut-addr tester-port sut-port)
> >> This is exactly the command show in the comment after
> >> the definition of sctp-as-v-1-1-2.
> >>
> >> I hope that helps...
> >>>
> >>>
> >>> Thanks a lot in advance,
> >>> /Norbert
> >>> _______________________________________________
> >>> sctp-discussion mailing list
> >>> sctp-discussion AT sctp.de
> >>> http://www.sctp.de/mailman/listinfo/sctp-discussion
> >>>
> >>
> >>
> >>
> >> --------------------------------
> >>
> >> _______________________________________________
> >> sctp-discussion mailing list
> >> sctp-discussion AT sctp.de
> >> http://www.sctp.de/mailman/listinfo/sctp-discussion
> >>
> >
>
>
>
> --------------------------------
>
> _______________________________________________
> sctp-discussion mailing list
> sctp-discussion AT sctp.de
> http://www.sctp.de/mailman/listinfo/sctp-discussion
>

---

• [SCTP-Discussion] How to use STT?, norbert . demeter, 12/01/2008
  • Re: [SCTP-Discussion] How to use STT?, Michael Tuexen, 12/01/2008
  • Aw: Re: [SCTP-Discussion] How to use STT?, norbert . demeter, 12/02/2008
    • Re: Aw: Re: [SCTP-Discussion] How to use STT?, Michael Tuexen, 12/02/2008
    • Aw: Re: Aw: Re: [SCTP-Discussion] How to use STT?, norbert . demeter, 12/02/2008
      • Re: Aw: Re: Aw: Re: [SCTP-Discussion] How to use STT?, Michael Tuexen, 12/02/2008

---

Archive powered by MHonArc 2.6.19+.